Browse back one page

Low Voltage Transformers: 13 to 29 volts

sort by:

Primary: 230 volts 50/60 Hz
Secondary: 13 volts c.t. @ 225A
Apparent Power: 2900 VA

Technical Material Corp. sealed transformer. 13 vac C.T. 2kv insulation. NSN: 6120-00-774-6497.

Primary: 68/136 volts @ 5 amps
Secondary: 13 volts
Quad 13v secondary outpus @ 15 amps

General Radio transformer. Four individual 13v @ 15 amp (very conservative!) winding can be run in series or parallel if needed. If run in series, 136 vac would be required to obtain full 13v out. By using a 0-140v variac, one could vary the primary up or down. Bottom (opposite terminals) has 1/4-20 threaded sockets.

Primary: 120 volts
Secondary: 15 volts @ 2A
Apparent Power: 30 VA

Tranex transformer. Primary: 120vac terminals 1 and 3. Secondary: 15 vac terminals 4 and 5, 2 amps. Used.

Primary: 115 volts (dual primaries)
Secondary: 17 volts @ 3A
Apparent Power: 50 VA

Single 17 vct secondary transformer.

Primary: 115 volts
Secondary: 11.5/16/50 volts
(one 11.5V @ 1A, one 16V c.t. @ 15A, and one 50V c.t. @ 100mA)

Power transformer. 4 tap, 420 Hz. NSN: 5950-00-755-4734.

Primary: 117 volts 50/60 Hz (Black leads)
Secondary: 18 volts @ 2A (Green leads)
Apparent Power: 36 VA

Transformer. Made in Japan.

Primary: 108/115/122 volts
Secondary: 18 volts @ 6A
Apparent Power: 100 VA

Transformer. Hermetically sealed, terminals. 1500v test.
NSN: 5950-00-246-5243.

Primary: 110 volts
Dual primary varies from 90-130v AC and 180-260v AC
Secondary: 19 volts

Regional Manufacturing transformer. PC mount. Triple secondary has variable rating, depending on loads. Manufacturer's ranges are listed based on 110 vac input. DUAL Primary can vary however from 90-130 vac and 180-260 vac. Secondary tracks accordingly. PC mount frame is 1-1/2" high x 2-1/4" x 1-7/8".

Primary: 115 volts
Secondary: 10/20 volts
20vct @ 200ma (series), 10v @ 440ma (parallel)

Signal transformer. 4.4 VA.

Primary: 120 volts
Secondary: 20 volts
Apparent Power: 5 VA

MCI transformer. Open frame, solder lugs, 3/16" push-on terminals.

Primary: 115 volts
Secondary: 20 volts
two 20V @ 374mA each (Parallel 20V @ 748mA or Series 40V @ 374mA)

Abbot open frame transformer. PC pins out bottom. NSN: 5950-01-032-8338.

Primary: 115/230 volts
Secondary: 20.5 volts
one @ 2.5A and one @ 650mA

Harris transformer. Harris P/N: 472-1070-000.

Primary: 208 volts 3-Phase
Secondary: 21.8 volts
Apparent Power: 177 VA

ADC transformer. Hermetically sealed, ultra-statically shielded. Terminals & posts on bottom. 5950-00-807-7849.

Primary: 115 volts
Secondary: 22/24 volts
(One 22V @ 25mA (brown) and One 24V c.t. @ 25mA (red-white-red)

Single Primary of 115 volt 50/60 hertz.  Two secondaries, one is 24 volt center tapped at 25 milliamps, the other is 22 volt 25 milliamp. Transformer. NSN: 5950-00-442-2024.

Primary: 120 volts
Secondary: 28 volts @ 12A
Apparent Power: 336 VA

QSE transformer. Spades on leads.

Primary: 115/230 volts
Secondary: 12/24 volts
12V @ 4.66A (parallel) or 24V @ 2.33A (series)

Signal Transformer PC mount transformer. 56 va.

Primary: 120 volts
Secondary: 24 volts @ 800mA
Apparent Power: 20 VA

Basler transformer.

Primary: 120 volts
Secondary: 4/8/12/16/20/24 volts
Apparent Power: 50 VA

Benjamin Products signaling transformer.

Primary: 120 volts
Secondary: 18-63 volts
@ 8A (AC or DC depending on hookup - See PDF)

Thordarson full wave bridge transformer. 26 lbs.

Primary: 120 volts
Secondary: 14/28 volts
Two 14v @ 350mA (Parallel 14V @ 700ma or Series 28V @ 350mA)

Jingshi open frame transformer. Dual winding. PC mount.

Primary: 120 volts
Secondary: 26 volts
Apparent Power: 26 VA

UTC transformer. Hermetically sealed. P/N: 72-0847-000.

Primary: 120 volts
Secondary: 22 volts c.t. @ 227mA
Apparent Power: 5 VA

General Dynamics aviation power transformer. 115v, 60 Hz to 22v, 227 ma CT. 5 wire loop terminals. Alt P/N's: TF4SX03YY, 6569, 5189357002.

Primary: 120 volts
Secondary: 28 volts c.t. @ 420mA
Apparent Power: 12 VA

Signal Transformer open frame transformer.

Primary: 120 volts 50 - 1000Hz
Secondary: 600/12.5 volts
one 600V c.t. @ 35mA, one 12.5V c.t. @ 2 amp

Jetronic hermetically sealed transformer. Terminals add posts on bottom. Two solder lug terminals. TF4RXO2HB

Primary: 115 volts
Secondary: 20 volts @ 5A
Apparent Power: 100 VA

Signal power transformer. 115v input, 20vct @ 5 amps. 2500v hi-pot. Solder-quick connect lugs.

Primary: 120 volts
Secondary: 20 volts c.t. @ 1A
Apparent Power: 20 VA

Magnetek transformer. 20vct, 1A, 1500v insulation.

Primary: 120 volts
Secondary: 24 volts @ 2.2A
Apparent Power: 55 VA

Ledex Dormeyer Control Transformer 24v AC, 55 VA. 11 3/4" leads

Primary: 120 volts
Secondary: 25 volts @ 1.75A
Apparent Power: 45 VA

Transformer. Marked: 28v AC, 50 watts. Fully loaded output is actually 25v @1.75 amps.

Primary: 120 volts
Secondary: 27 volts @ 2A
Apparent Power: 50 VA

Transformer. 27v AC 2 amps, 120vac

Primary: 24 volts
Secondary: 25/370/740 volts
one 25V @ 10mA and one 740V c.t. (370-0-370) @ 75mA

Thordarson plate / filament transformer. New!! Sealed, rounded corners. Made in the 1950's.

Primary: 117/234 volts 50/60 Hz
Secondary: 9/18 volts
(two 9V @ 1.67A or one 9V @ 3.3A or one 18V @ 1.67A)

Two 117v 50/60Hz International Primaries; Two secondaries 9v, 1.67amp, 30VA. 3"DIA x 1.5"H 1.1lbs. UL & CSA recognized/certified. 10" Color coded leads. Class A 105°C. Primaries must be connected in series or parallel.

Primary: 117/234 volts 50/60 Hz
Secondary: 9/18 volts
(two 9V @ 5.3A or one 9V @ 10.6A or one 18V @ 5.3A)

Two 117v 50/60Hz International Primaries; Two secondaries 9v, 5.3amp, 95VA. 3.9"DIA x 1.5"H 2.2lbs. UL & CSA recognized/certified. 10" Color coded leads. Class A 105°C. Primaries must be connected in series or parallel.

Primary: 117/234 volts 50/60 Hz
Secondary: 15/30 volts
(two 15V @ 3.2A or one 15V @ 6.4A or one 30V @ 3.2A)

Two 117v 50/60Hz International Primaries; Two secondaries 15v, 3.2amp, 95VA. 3.9"DIA x 1.5"H 2.2lbs. UL & CSA recognized/certified. 10" Color coded leads. Class A 105°C. Primaries must be connected in series or parallel.

Primary: 117/234 volts 50/60 Hz
Secondary: 18/36 volts
(two 18V @ 3.9A or one 18V @ 7.8A or one 36V @ 3.9A)

Two 117v 50/60Hz International Primaries; Two secondaries 18v, 3.9amp, 140VA. 3.9"DIA x 1.9"H 3lbs. UL & CSA recognized/certified. 10" Color coded leads. Class A 105°C. Primaries must be connected in series or parallel.

Primary: 117/234 volts 50/60 Hz
Secondary: 15/30 volts
(two 15V @ 10A or one 15V @ 20A or one 30V @ 10A)

Two 117v 50/60Hz International Primaries; Two secondaries 15v, 10amp, 300VA. 4.6"DIA x 2.6"H 5.7lbs. UL & CSA recognized/certified. 10" Color coded leads. Class A 105°C. Primaries must be connected in series or parallel.

Primary: 117/234 volts 50/60 Hz
Secondary: 24/48 volts
(two 24V @ 13A or one 24V @ 26A or one 48V @ 13A)

Two 117v 50/60Hz International Primaries; Two secondaries 24v, 13amp, 625VA. 5.5"DIA x 3.2"H 9.5lbs. UL & CSA recognized/certified. 10" Color coded leads. Class A 105°C. Primaries must be connected in series or parallel.

Primary: 120/230 volts AC 50/60 Hz
Secondary: 6.3/14.8/64/195/390 volts (6.3v @ 3.6A, 14.8v @ 2A, 64v @ 100mA, 195 @ 500mA, and 195/390 @ 1.5A)
Apparent Power: 740 VA

Tortran vacuum tube amplifier transformer. Center epoxy potted with 3/8" mount hole. Dual primaries 115v (230v in series) 50/60Hz 740va. Five secondaries 390v C.T. at 1.5 amps, 195v at 0.5 amps, 14.8v at 2 amps, 6.3v at 3.6 amps, 64v at 0.1 amps. 6.1"DIA x 3"H, 14 lbs.

Primary: 110/230 volts 60 Hz
Secondary: 18/36 volts
(two 18V @ 139mA or one 18V @ 278mA or one 36V @ 139mA)

110/230v 60Hz Primary; Two secondaries 18v, 139ma, (No load 25.5v, 2ma), 70% eff. For 110v supply power, primaries must be parallel; for 230v operation, primaries must be in series. OD: 47.mm ID: 6.mm x 18mm H

Primary: 110/230 volts 60 Hz
Secondary: 7/14 volts
(two 7V @ 500mA or one 7V @ 1A or one 14V @ 500mA)

110/230v 60Hz Primary; Two secondaries 7v, 500ma, (No load 9.5v, 3ma), 74% eff. For 110v supply power, primaries must be parallel; for 230v operation, primaries must be in series. OD: 47.mm ID: 6.mm x 21.5mm H

Primary: 110/230 volts 60 Hz
Secondary: 12/24 volts
(two 12V @ 417mA or one 12V @ 834mA or one 24V @ 417mA)

110/230v 60Hz Primary; Two secondaries 12v, 417ma, (No load 14.4v, 3ma), 82% eff. For 110v supply power, primaries must be parallel; for 230v operation, primaries must be in series. OD: 53.5mm ID: 6.8mm x 23.5mm H

Primary: 110/230 volts 60 Hz
Secondary: 12/24 volts
(two 12V @ 2.08A or one 12V @ 4.16A or one 24V @ 2.08A)

110/230v 60Hz Primary; Two secondaries 12v, 2.08amp, (No load 13.8v, 8ma), 86% eff. For 110v supply power, primaries must be parallel; for 230v operation, primaries must be in series. OD: 78.mm ID: 22.5mm x 35.mm H

Primary: 110/230 volts 60 Hz
Secondary: 18/36 volts
(two 9V @ 2.77A or one 9V @ 5.54A or one 18V @ 2.77A)

110/230v 60Hz Primary; Two secondaries 9v, 2.777amp, (No load 10.4v, 8ma), 86% eff. For 110v supply power, primaries must be parallel; for 230v operation, primaries must be in series. 82.4mmL x 82.4mmW x 37.5mmH, UL & VDE certifications, Maximum ambient temperature of 40°C

Primary: 110/230 volts 60 Hz
Secondary: 15/30 volts
(two 15V @ 1.66A or one 15V @ 3.32A or one 30V @ 1.66A)

110/230v 60Hz Primary; Two secondaries 15v, 1.667 amp, (No load 17.3v, 8ma), 86% eff. For 110v supply power, primaries must be parallel; for 230v operation, primaries must be in series. 82.4mmL x 82.4mmW x 37.5mmH, UL & VDE certifications, Maximum ambient temperature of 40°C

Primary: 110/230 volts 60 Hz
Secondary: 18/36 volts
(two 18V @ 89mA or one 18V @ 178mA or one 36V @ 89mA)

110/230v 60Hz Primary; Two secondaries 18v, 89ma, (No load 25.7v, 1.5ma), 70% eff. For 110v supply power, primaries must be parallel; for 230v operation, primaries must be in series. 44.7mmL x 44.7mmW x 19.5mmH, UL & VDE certifications, Maximum ambient temperature of 60°C

Primary: 110/230 volts 60 Hz
Secondary: 12/24 volts
(two 12V @ 133mA or one 12V @ 266mA or one 24v @ 133mA)

110/230v 60Hz Primary; Two secondaries 12v, 133ma, (No load 17.3v, 1.5ma), 70% eff. For 110v supply power, primaries must be parallel; for 230v operation, primaries must be in series. 44.7mmL x 44.7mmW x 19.5mmH, UL & VDE certifications, Maximum ambient temperature of 60°C

Primary: 110/230 volts 60 Hz
Secondary: 12/24 volts
(two 12V @ 208mA or one 12V @ 416mA or one 24V @ 208mA)

110/230v 60Hz Primary; Two secondaries 12v, 208ma, (No load 17v, 2ma), 68% eff. For 110v supply power, primaries must be parallel; for 230v operation, primaries must be in series. 49.7mmL x 49.7mmW x 19.5mmH, UL & VDE certifications, Maximum ambient temperature of 60°C

Primary: 110/230 volts 60 Hz
Secondary: 18/36 volts
(two 18V @ 139mA or one 18V @ 278mA or one 36V @ 139mA)

110/230v 60Hz Primary; Two secondaries 18v, 139ma, (No load 25.5v, 2ma), 68% eff. For 110v supply power, primaries must be parallel; for 230v operation, primaries must be in series. 49.7mmL x 49.7mmW x 19.5mmH, UL & VDE certifications, Maximum ambient temperature of 60°C

Primary: 110/230 volts 60 Hz
Secondary: 22/44 volts
(two 22V @ 114mA or one 22V @ 228mA or one 44v @ 114mA)

110/230v 60Hz Primary; Two secondaries 22v, 114ma, (No load 29.7v, 2ma), 68% eff. For 110v supply power, primaries must be parallel; for 230v operation, primaries must be in series. 49.7mmL x 49.7mmW x 19.5mmH, UL & VDE certifications, Maximum ambient temperature of 60°C

Primary: 110/230 volts 60 Hz
Secondary: 18/36 volts
(two 18V @ 417mA or one 18V @ 834mA or one 36V @ 417mA)

110/230v 60Hz Primary; Two secondaries 18v, 417ma, (No load 22.2v, 4ma), 80% eff. For 110v supply power, primaries must be parallel; for 230v operation, primaries must be in series. 60mmL x 60mmW x 26.3mmH, UL & VDE certifications, Maximum ambient temperature of 60°C

Primary: 110/230 volts 60 Hz
Secondary: 18/36 volts
(two 18V @ 972mA or one 18V @ 1.94A one 36V @ 972mA)

110/230v 60Hz Primary; Two secondaries 15v, 1.667 amp, (No load 17.3v, 8ma), 86% eff. For 110v supply power, primaries must be parallel; for 230v operation, primaries must be in series. 82.4mmL x 82.4mmW x 37.5mmH, UL & VDE certifications, Maximum ambient temperature of 40°C

Primary: 120/240 volts
Secondary: 27 volts
Apparent Power: 700 VA

Vishay Medical power transformer. Primary: 120/240v. 120v: Terminals 1&3; Line 1. Terminals 2&4; Line2. 240v: strap 2-3; Line 1&4. Secondary: 27 vac @ 25 amps. 12 AWG secondary. Spade QC terminals.

Primary: 115/230 volts 50/60 Hz
Secondary: 24v @ 0.5 amp / 12v @ 1 amp
2000v Hi-pot

Stancor transformer. 115/250vAC to 24V @ 0.5 Amps/ 12v @ 1 Amp. 200v hi-pot. Low profile PC mount. 2" x 2-1/2" x 1"

Primary: 117 volts
Secondary: 24v c.t. @ 85 mA
Dimensions: 1.375"D x 2.062"W x 1.187"H

Triad miniature power transformer. 117v to 24v c.t. @ 85 mA. 50/60 Hz. 1.375"D x 2.062" x 1.187"H.

Primary: 115/230 volts
Secondary: 24v c.t. @ 1 amp RMS
50/60 Hz

Triad filament transformer. 115/230v to 24v c.t. @ 1 amp RMS. 50/60 Hz. 2"W x 3.31" x 1.937"H.

Primary: 120 volts
Secondary: 24vAC @ 300ma
Dimensions:1-7/16" x 1"W x 1-3/16"H

Hytronics power  transformer.  120vAC to 24vAC @ 300ma. Through hole mount.  1-7/16" x 1"W x 1-3/16"H. New old stock.

Primary: 115 volts
Secondary: 16.5v L-L @ 4.5 amps / 74v A 10.6 amps
60 Hz

UTC hermetically sealed transformer. 115v to 16.5v/74v @ 4.5a/10.5ma RMS. 3 phase. Delta. 60 Hz. 2" x 4" x 4". NSN: 5950-00-419-0174.

Primary: 117 volts
Secondary: 12/24 volts
8/4 amps

Stancor dual power transformer. 117vAC to 12/24vAC @ 8/4 amps or variable 11.7-29.2v according to primary tap. 50/60-400Hz. 7 lead. 4-1/4" x 3-1/8" x 3-3/4"H.

Primary: 120 volts
Secondary: 24 volts leads
50/60 Hz

Honeywell HVAC power transformer. Primary: 120v, 50/60 Hz. Secondary leads: 24v. 39va transformer. 4x4 plate mounting.

Primary: 115/230 volts
Secondary: 26.4 volts @ 1.7/1.35a
50/60 Hz

Thordarson power transformer. Primary: 115/230v, 50/60 Hz. Secondary: 26.4v @ 1.7/1.35a. Hermetically sealed. Electrostatically shielded. Turret terminals. NSN: 5950-00-645-3854.

Primary: 120/208/240 volts
Secondary: 24 volts
Apparent Power: 75 VA

Honeywell/Tradeline HVAC universal circuit breaker transformer. Primary: 120/208/240v. Secondary: 24 vac @ 75 amps. 50/60 Hz. Built in circuit breaker. Foot mount on conduit/panel mount.

Primary: 117 volts
12.6V @ 1 amp
50/60 Hz

Filament transformer. Primary 117 volt to secondary 12.6 volt  at 1 amp. 50/60 Hz. Made in Japan, circa 1970. 2-1/8" mounting centers. Dimensions: 3" x 1-1/2" x 1-7/8" high.

Primary: 115 volts
Secondary: 15v @ 100ma RMS or 30vct @ 50ma RMS
50/60 Hz

Triad Power Transformer 115v @ 50/60Hz  to 15v @ 100ma RMS or 30vct @ 50ma RMS

Primary: 117 volts
Secondary: 11.7-29.4vct @ 2 amps or 11.1-28.5v @ 1.25 ADC Bridge
60 Hz

Stancor rectifier transformer. 60Hz.

Primary: 220v, 50-400 Hz, 3 phase Delta
Secondary: 21.0v RMS, 3 phase Wye
Apparent Power: 5 amps RMS

SNC 50-400 Hz transformer. Primary: 220v, 50-400 Hz, 3 phase Delta. Secondary: 21.0v RMS, 3 phase Wye. 5 amps RMS. Mounting centers 1-1/8" x 3-3/8". Made for Gates.

Primary: 115 volts
Secondaries: 20vct @ 10 amps, 21v @ 2 amps
Dimensions: 3-3/4" x 4-1/2" x 4-1/2"H

Lambda transformer. Primary: 115v AC Black-White. Secondaries:  20v CT @ 10 amps Red-Red, White-Yellow, 21v @ 2 amps Green-Green. Brown - no connection. Mounts vertically or horizontally. Made for Lambda power supply.

Primary: 88/110/120/130/220/240/260 volts
Secondary: 20.8 volts
Apparent Power: 3.3 VA

Tele-Signal Corp. transformer. 47-63 Hz. 2 primaries: 88/110/120/130/220/240/260. Raise / lower secondary by changing primary taps. Secondary: 20.8v @ 3.3 amps. Hermetically sealed. Fork terminals. 3-1/2" x 3" x 3-11/16". 2-1/8" x 2-5/8" mounting centers.

Primary: 115 volts
Secondaries: 27v @ 2 amp and 22v @ 1 amp
Dimensions: 2-5/8" x 3" x 2-1/2"H

Coil Specialists transformer. Electrostatically shielded (white / grey). Primary: White / Black 115v AC @ 60 Hz. Secondaries: Red: 27v @ 2 amp, White / Green: 22v @ 1 amp. 2-5/8" x 3" x 2-1/2"H.

Primary: 110/115/120/125 volts
Secondary: Red/White-Red: 32v c.t. @ 3 amp
Secondary: Blue/White-Blue: 24v c.t. @ 4 amp

Tranex transformer. Primary: 110/115/120/125v. Secondaries: Red/White-Red: 32v c.t. @ 3 amp, Blue/White-Blue: 24v c.t. @ 4 amp, Orange: 8v @ 10 amp. 3-3/4" x 4" x 4-1/2". 10 lbs.

Primary: 115 volts
Secondary: 24 volts
Apparent Power: 18 VA

Transformer. Primary (Black): 115v AC. Secondary (Red): 24v @ 0.75 amps. Circa 1960. 3-3/8" x 3-1/2" x 3-1/4".

Primary: 115 volts
Secondary 5-6: 120v @ 0.2 amps
Secondary 9-10: 7v @ 0.5 amps

Power transformer. Primary 1,2: 115v AC, 3,4: 115v AC (115/230). Secondaries: 5,6: 120v @ 0.2 amp; 9-10: 7v @ 0.5 amp; 11-12: 20v @ 3 amp; 13,14: 20v @ 3 amp; 15-16: 9v @ 1 amp. 3-7/16" x 3" x 4-1/4". Weighs 5.7 lbs.

Primary: 115 volts
Secondary: 20 volts
Apparent Power: 12 VA

UTC Power Transformer. Type H-142. Hermetically sealed, transistor supply transformer. Primary: 115v, 50/60 Hz. Secondary: 20v c.t., 0.6 amps. Milspec: MIL-T-27-A.

Dual 8v c.t. @ 4 amps
Series: 16v c.t. @ 4 amps
Parallel: 8v c.t. @ 8 amps

Signal transformer. Dual 8v c.t. @ 4 amps. Series: 16v c.t. @ 4 amps. Parallel: 8v c.t. @ 8 amps.

Primary: 115 volts
Secondary: 24v @ 6 amp & 5v @ 10 amp
Dimensions: 5.5" x 3.6" x 3.3"H

Transformer assembly. Made for Lexmark. (Also 528PB56). 115v AC input @ 48 - 90 Hz. Includes switch, 1.25 amp fuse and socket for standard machine cord. Output to 7 position molex connector. Solid copper electrostatic shield on outside of EI core to reduce typical  60 Hz interference on equipment. Made in Italy. Large quantity in stock.

Primary: 115 volts
Secondary: 28v @ 6 amp
Dimensions: 5.25" x 3.8" x 3"H

Power Transformer. Made for Lexmark. 115v input @ 50/60 Hz. Includes switch and cord. Output to 5 pin molex connector. Solid copper electrostatic shield on outside of EI core to reduce typical  60 Hz interference on equipment. Large quantity in stock.

Primary: 115 volts
Secondary: 28v @ 6 amp
Dimensions: 5.25" x 3.8" x 3"H

Power Transformer. Made for Lexmark. 115v input @ 50/60 Hz. Includes switch and 2 pin AC plug which accepts standard machine cord (3 blade). This transformer will NOT be grounded through this connector.

Primary: 115/230 volts
Secondary: 28 volts
Apparent Power: 28 VA

Basler transformer. 115v black & black stripe, red & red stripe. 1/4" spade terminals on output.

Primary: 115/230 volts
Secondary: 24 volts
Apparent Power: 30 VA

Magnetek SPA replacement transformer. Mounts via frame holes on 1.70" centers. 1/4" spade connectors.

Primary: 120/240 volts
Secondary: 16/32 volts
Apparent Power: 100 VA

General Electric power transformer. Type QB. 100vA. UL listed.

Primary: 208 / 240v @ 60 Hz
Secondary: 18.4v c.t. @ 326 amps
Dimensions: 9-1/2" x 13-1/2" x 14-1/2"H overall

Continental Electronics filament transformer. 6 kva. General Electric

Primary: 208 / 230v
Secondary: 18.4v c.t. @ 320 amps
Dimensions: 13" x 9-1/2" x 14-1/2"H overall

General Electric for Continental Electronics filament transformer. 6 kva. Spare for Continental 420. Used.

Primary: 120 volts
Secondary: 21v, 23v or 25v @ 100 mA
Dimensions: 1-9/16" x 1-9/16" x 2-3/8"H

Microtran multi-tapped transformer. Hermetically sealed. 120v @ 60 - 400 Hz Primary.

Primary: 120 volts
Secondary: 24 volts
Apparent Power: 38 VA

Honeywell power transformer.

Primary: 115v @ 60 Hz
Secondary: 6.5 / 13 / 19.5 / 26v @ 3 amps RMS Int.
Dimensions: 2-1/2" x 2-3/4" x 3-3/8"H

Triad dry disk rectifier. 1500v test. Brand new in the box!

Primary: 120/240 volts
Secondary: 12/24 volts
Apparent Power: 150 VA

Powerformer buck boost. 150vA. Enclosed.

Primary: 115 volts @ 50/60 Hz
Dual Secondary: 32v c.t. @ 1 amp & 15v c.t. @ 4 amps
Dimensions: 3" x 3" x 3-3/4"H

Triad transformer. Dual secondary.

Primary: 117 volts @ 60 Hz
Secondary: 12.1 to 29.0 volts c.t. @ 22.5 amps (F.W.C.T) or 12.0 to 29.0 volts @ 12 amps DC (Bridge)
Dimensions: 5-1/2" x 4-1/2" x 5-1/4"H

Stancor transformer.

Primary: 117 volts, 50/60 Hz
Secondary: 25.2 volts c.t. @ 1 amp
1500 volts RMS test

Triad filament transformer. 1500 volts RMS test. 2-13/16" mounting centers.

Primary: 117 volts
Secondary: 12 to 29.7 volts @ 12 amps (F.W.C.T) or 12 to 29.7 volts @ 6 amps (Bridge)
Dimensions: 3-1/2" x 4" x 4-1/8"H

Stancor transformer.

Primary: 117 volts, 50/60 Hz
Secondary: 28 volts c.t. @ 6 amps
Dimensions: 3-3/8" x 3-1/2" x 4-1/8"H

Stancor power transformer. 1500 volts test.

Primary: 100 / 110 / 120 volts, 50/60 Hz
Secondary: 22 volts @ 5.1 amps and 120 volts @ 0.5 amps and 8.15 volts @ 9.35 amps
Dimensions: 5"D x 1-7/8"H

Ulveco toroidal transformer.

Primary: 120 / 240 volts
Secondary: 2 x 28.4 volts @ 2.67 amps
160 va

Avel Lindberg toroidal transformer.

Primary: 120 volts AC @ 60 Hz
Secondary: 2 x 24 volts AC @ 3.3 amps
160 watts

ILP toroidal power transformer. 160 watts. Great for stereo amps!

Primary: 100 / 110 / 120 volts @ 50/60 Hz
Secondary: 120 volts @ 3.5 amps, 21 volts @ 19 amps, 8.5 volts @ 10.5 amps, 37 volts @ 3 amps, 12 volts @ 0.2 amps
1062 va

Amveco Magnetics toroidal transformer.

Input: 115 / 230v @ 50/60 Hz
Output: 2 x 12v c.t. @ 100 amps
Wire in Series: 24v c.t. @ 50 amps

Signal transformer. 2 x 12v c.t. output.

Primary: 115 / 230v @ 50/60 Hz
Secondary: Dual 14v @ 0.42 amps Windings, 14v @ 0.84 amps or 28v c.t. @ 0.42 amps
Dimensions: 1-7/8" x 1-5/8"

Stancor PC mount transformer. Dual windings.

Primary: 100/120/220/240v
Secondaries: 27.8vct @ 100ma, 28.9v @ 600ma, 19.4v @ 6a
Dimensions: 4.5" x 4" x 3.75"H

Schott Corp. power transformer.

Primary: 115v AC, 50/60 Hz
Secondary: 24v c.t. @ 4 amps, 115v
Dimensions: 2-1/2" x 3-1/4" x 3-3/4"H

Triad transformer. Only one available.

High Volts: 120 / 240v Input
Low Volts: 12 / 24v Output
250 vA

Square D dry type transformer. 60 Hz.

Primary: 115 / 230v, 50/60 Hz
Secondary: 24v AC @ 1.25 amps
Dimensions: 2-3/16" x 1-7/8" x 1-7/8"H

Jandy transformer. Replacement for Laars Boiler.

Primary: 115v AC, 60 Hz
Secondary: 24v AC @ 40vA
1.67 amps

HVAC transformer. 3-1/8" mounting centers

Polyphase Inc

(COL) 662-0977-010

Primary: 100/115 volts
Apparent Power: 47-420Hz VA
Manufactured by

Polyphase Inc. pn R5338 term. Made for Rockwal Collins 4 windings 16-412v term 1, 2, 3. 4.56" x 4.38" x 3.88"H.

  • 1: 12a - 17v DC (20vct) 6, 7, 8
  • 2: 5a - 16v DC (18 vct) 9, 10, 11
  • 3: .5a - 46v DC (55vct) 12, 13, 14
  • 4:  30ma 412v DC (450vac) 15, 16

Primary: 115 volts
Secondary: .8 amps volts
Apparent Power: 50/60 Hz VA

Power transformer 24v DC, .8 amps. Hermetically sealed. Mfg VTC. 2 x 2 x 2 5/8"H. Primary: 115v AC. 50/60Hz.

Primary: 105/115/125 volts
Secondary: 28 vct @ 40 amps or 56v @ 20 amps volts
Manufactured by SWE

SWE 0403D, 700006B transformer. Parallel 28 vct @ 40 amps or 56v @ 20 amps. Series two 28 vct @ 20 amps windings. 6-3/85" x 7-3/4" x 5-1/4"H. Primary 105, 115, 125v AC.

Primary: 110v AC, 60 Hz volts
Secondary: 20 vct @ 50 amps, 5 vct @ 300 amps volts
Apparent Power: 2000 VA

Crittenden 14711 Dual winding 20 vct @ 50 amps and 5 vct @ 300 amps, 2 KVA total capacity. 6" x 10" x 9-1/4"H. Primary 110v AC, 60 Hz.

 
For more information
E-mail: [email protected]

Home Page | Alphabetical Listing | Blog | View Cart | Ordering Information

© 2003-2016 Surplus Sales of Nebraska