Laser Housing Components
All sales are as-is-where-is and sold without warranty expressed or implied. All items listed on laser pages are used at buyers own risk and Surplus Sales or its affiliates will not be held liable.
Opposing Wedge Clamps
 |
 |
Aluminum wedges when tightened cause the height of the device to increase (similar to a wedge jack). Used to brace inner laser assembly to the housing. Center hole allows piece of allthread and nuts to squeeze wedges together.
| Part Number | Length at Sq. |
Width |
Min. Height |
Max Height |
Description / Notes |
Price |
||
| LZR-WEDCLMP6679 | pics | 5-15/16" | 1-1/8" | 1.40" | 1.58" | No hardware included | 150.00 |
|
| LZR-WEDCLMP6375 | pics | 3-3/16" | 2" | 0.74" | 0.88" | Threaded shaft and nuts included | 95.00 |
|
| LZR-WEDCLMP6000 | pics | 3" | 2" | 0.4" | 0.54" | Threaded shaft and nuts included | 125.00 |
|
| LZR-WEDCLMP4000 | pics | 2" | 2" | 0.7" | 0.87" | No hardware, one wedge has two 1-1/8" O.C. countersunk flathead screws | 95.00 |
|
| LZR-WEDCLMP3046 | pics | 4-7/8" | 5/8" | 0.96" | 1.13" | No hardware included | 85.00 |
|
| LZR-WEDCLMP3000 | pics | 4" | 3/4" | 0.7" | 0.875" | Rounded top / bottom, no hardware included | 110.00 |
|
| LZR-WEDCLMP2812 | pics | 3-3/4" | 3/4" | 0.71" | 0.88" | No hardware included | 80.00 |
|
| LZR-WEDCLMP2718 | pics | 3-5/8" | 3/4" | 0.68" | 0.88" | Threaded shaft and nuts included | 75.00 |
|
| LZR-WEDCLMP1500 | pics | 2" | 3/4" | 0.61" | 0.75" | Threaded shaft and nuts included | 75.00 |
Minimum and maximum height measured using 0.1" diameter rod, or included hardware. Some wedge shafts are threaded 1/4-20. All shafts 0.2" diameter.
Aluminum Holding Rings
(LZR) ALRING1
1.75" diameter x 0.31" thick, 1.05" diameter center hole. (4) 0.17" diameter bolt holes 1" c-c. 1.14" groove about 0.03" deep around center hole on one side. Used for holding insulated stand off posts. Pictured left.
$30
Aluminum Holding Rings (Cont'd)
(LZR) ALRING2
1.75" diameter x 0.37" thick, 0.80" diameter center hole. 1.09" diameter x 0.185" deep outer groove / bore. Pictured center.
$30
(LZR) ALRING3
1.75" diameter x 0.31" thick, 1.03" diameter center hole. 1.14" x 0.12" deep outer groove. Pictured right.
$30
(LZR) HOLDRING13
1.5" outside diameter with (8) 0.17" diameter evenly spaced bolt holes. Pattern matches LZR-MIRM-A and LZR-MIRM-B lens cap. 0.25" thick with 0.5" beveled inner hole.
$19
Mirror Holding Cap
(LZR) M25HOLD
2.5" outside diameter x 1/2" thick x 1" inside diameter. Has groove 0.13" thick x 1.51" to hold a 1.5" diameter mirror. (4) 0.17" diameter mount holes, 1.5" c-c square pattern. Aluminum.
$25
(LZR) M13HOLD-A
1.3" outside diameter x 0.092" thick x 0.44" inside diameter. Has groove 0.05" thick x 0.767" to hold a 0.75" diameter mirror. (8) 0.103" diameter mount holes evenly spaced around diameter of ring. Hole pattern matches LZR-MIRM-A and LZR-MIRM-B lens holder pattern. Aluminum.
$19
(LZR) M13HOLD-B
1.3" outside diameter x 0.092" thick x 0.44" inside diameter. Has groove 0.05" thick x 1.007" to hold a 1.0" diameter mirror. (8) 0.103" diameter mount holes evenly spaced around diameter of ring. Hole pattern matches LZR-MIRM-A and LZR-MIRM-B lens holder pattern. Aluminum.
$19
Chamber Tube
(LZR) CHBTUB
18-1/2" long x 5" diameter (4-1/2" inside diameter). Has 1/2" wide groove 3/4" from each end to accomodate an end wall clamp, used to bolt an end wall to the end. Has a 2-1/8" groove in the center and a 1/2" port hole for an electrode feed through.
$55
Chamber Tube End Wall Clamp
(LZR) EWLCLMP
7" x 7" x 1/2" overall with an inner center hole 4.7" diameter for clamping to LZR-CHBTUB (above). Two pieces of aluminum with clamp bolts.
$30
Circular Tube End Wall
(LZR) ENDWL
6-7/8" diameter x 3/4" thick with inner 4-1/2" centered ring 1/8" high which mates to LZR-CHBTUB (above) inner diameter with an O-ring to form a vacuum seal. Has a 2.25" inside diameter bore which is offset from the center by 11/16". The outside of the bore has 8 evenly spaced threaded bolt holes for mounting an end cap or window. Also has a 3/8" threaded port hole for vacuum and gas valves. Solid aluminum.
$65
Aluminum Wall / End Cap
(LZR) ALREC3
3.18" diameter x 0.75" thick. 2.45" diameter groove for o-ring. (4) 0.19" diameter bolt holes, 2" c-c with 0.31" countersink on reverse side of o-ring. Solid aluminum.
$24
Laser Chamber Hole Plug
(LZR) ALPLUG1
1.75" diameter x 0.37" thick with centered 0.743" diameter x 0.625" long plug with o-ring. (4) 0.17" diameter bolt holes in square 1" c-c pattern. Used to plug a 3/4" (0.75") beveled chamber hole. Aluminum.
$25
Laser Chamber Rail Kit
(LZR) RAILKIT1
16-13/16"L x 1-1/2"W x 3/8"H base with two sets of side rails - your option which to use, see PDF for dimensions and specifications. 5 Aluminum pieces.
$179
Laser Chamber Rail Kit
(LZR) RAILKIT2
16-13/16"L x 1-1/2"W x 2-1/8"H base with two sets of side rails - your option which to use, see PDF for dimensions and specifications. 5 Aluminum pieces.
$199
Laser Chamber Rail Kit
(LZR) RAILKIT3
16-7/8"L x 1-1/2"W x 1-1/4"H base with only one set of side rails, see PDF for dimensions and specifications. Assembled.
$159
Electrode Rail
(LZR) RAIL11A
11-3/4"L x 1/4"W x 1/16" base height. One aluminum rail piece, no connecting point.
$9
Laser Housing Electrode Rail
(LZR) RAIL9A
9-1/8"L x 1/2"W x 0.6"H. Rounded top and upper edges and corners. Bottom 1/4" block has square (sharp) edges. Solid aluminum, 3 tapped holes on bottom.
$69
Laser Housing Electrode Rail
(LZR) RAIL14-1A
14-7/8"L x 1-1/2"W x 0.75"H1 with an inner, rounded edges peak centered on top 13-7/8"L x 1/4"W which totals 1"H2 overall. Solid aluminum 1.7 lbs.
$95
(LZR) RAIL14-1S
14-7/8"L x 1-1/2"W x 0.75"H1 with an inner, rounded edges peak centered on top 13-7/8"L x 1/4"W which totals 1"H2 overall. Solid stainless steel 4.85 lbs.
$125
Laser Housing Electrode Rail
(LZR) RAIL14-2S
14-1/8"L x 1"W x 1/8"H base with peaking elecrode 13-3/4"L x 1/2"W x 0.6" overall height, centered on base. Stainless steel, no screw points on bottom.
$95
(LZR) RAIL14-4A
14-7/8"L x 7/8"W x 1/4"H base with square electrode peak 13-13/16"L x 0.20"W x 0.15"H making overall height of 3/8" (non-round / sharp corners). Aluminum, no screw points on bottom.
$34
Laser Housing Electrode Rail
(LZR) RAIL18A
18-5/8"L x 1/2"W x 0.60"H. Rounded top and side corners and edges. 6 screw points on bottom, 6-32nd threaded. 5 on 4" c-c and the last 2-1/2" c-c. Solid aluminum.
$89
(LZR) RAIL27A
27-1/4"L x 1/2"W x 0.60"H. Rounded top and side corners and edges. 7 screw points on bottom, 6-32nd threaded. 5 on 4" c-c and the last 6" c-c. Solid aluminum.
$99
Electrode Rail
(LZR) RAIL12A
11-3/4"L x 0.06"W x 1/4" base height with 0.25"L x 0.06"W x 0.25"H connecting point in center of rod's length. Overall 1/2" height at connecting point. Aluminum. Would typically be embedded in (like LZR-81001-01) or between alumina ceramic.
$14
Electrode Rail (Cont'd)
(LZR) RAIL13A
11-3/4"L x 0.06"W x 1/4" base height with off-center 0.25"L x 0.06"W x 0.25"H connecting point. 4-1/4" from left side,
7-1/4" from right.
7-1/4" from right.
$14
(LZR) RAIL14-3A
14-3/4"L x 0.06"W x 0.1" base height with 0.25"L x 0.06"W x 0.25" connecting point in center of rod's length. Aluminum. Would typically be placed in a groove within an alumina ceramic wall or spaced between two pieces of alumina.
$18
(LZR) RAIL16A
16-1/16"L x 0.06"W x 1/8" base height with off-center 0.25"L x 0.06"W x 0.25"H connecting point. 8-1/4" from left side,
7-1/2" from right.
7-1/2" from right.
$20
Electrode Rail
(LZR) RAIL13S
13-7/8"L x 0.19"W x 5/8"H. One stainless steel rail piece, no connecting point.
$16
Electrode Rail
(LZR) RAIL14-7S
14-1/8"L x 1/8"W x 3/4"H with completely (half-circle) rounded edges. One polished stainless steel rail piece, no connecting point.
$30
All sales are as-is-where-is and sold without warranty expressed or implied. All items listed on laser pages are used at buyers own risk and Surplus Sales or its affiliates will not be held liable.