Laser Housing Components

Product Details:
1.75" diameter x 0.31" thick, 1.05" diameter center hole. (4) 0.17" diameter bolt holes 1" c-c. 1.14" groove about 0.03" deep around center hole on one side. Used for holding insulated stand off posts. Pictured left.

Product Details:
1.75" diameter x 0.37" thick, 0.80" diameter center hole. 1.09" diameter x 0.185" deep outer groove / bore. Pictured center.

Product Details:
1.75" diameter x 0.31" thick, 1.03" diameter center hole. 1.14" x 0.12" deep outer groove. Pictured right.

Product Details:
1.5" outside diameter with (8) 0.17" diameter evenly spaced bolt holes. Pattern matches LZR-MIRM-A and LZR-MIRM-B lens cap. 0.25" thick with 0.5" beveled inner hole.

Product Details:
2.5" outside diameter x 1/2" thick x 1" inside diameter. Has groove 0.13" thick x 1.51" to hold a 1.5" diameter mirror. (4) 0.17" diameter mount holes, 1.5" c-c square pattern. Aluminum.

Product Details:
1.3" outside diameter x 0.092" thick x 0.44" inside diameter. Has groove 0.05" thick x 0.767" to hold a 0.75" diameter mirror. (8) 0.103" diameter mount holes evenly spaced around diameter of ring. Hole pattern matches LZR-MIRM-A and LZR-MIRM-B lens holder pattern. Aluminum.

Product Details:
1.3" outside diameter x 0.092" thick x 0.44" inside diameter. Has groove 0.05" thick x 1.007" to hold a 1.0" diameter mirror. (8) 0.103" diameter mount holes evenly spaced around diameter of ring. Hole pattern matches LZR-MIRM-A and LZR-MIRM-B lens holder pattern. Aluminum.

Product Details:
18-1/2" long x 5" diameter (4-1/2" inside diameter). Has 1/2" wide groove 3/4" from each end to accomodate an end wall clamp, used to bolt an end wall to the end. Has a 2-1/8" groove in the center and a 1/2" port hole for an electrode feed through.

Product Details:
7" x 7" x 1/2" overall with an inner center hole 4.7" diameter for clamping to LZR-CHBTUB (above). Two pieces of aluminum with clamp bolts.

Product Details:
6-7/8" diameter x 3/4" thick with inner 4-1/2" centered ring 1/8" high which mates to LZR-CHBTUB (above) inner diameter with an O-ring to form a vacuum seal. Has a 2.25" inside diameter bore which is offset from the center by 11/16". The outside of the bore has 8 evenly spaced threaded bolt holes for mounting an end cap or window. Also has a 3/8" threaded port hole for vacuum and gas valves. Solid aluminum.

Product Details:
3.18" diameter x 0.75" thick. 2.45" diameter groove for o-ring. (4) 0.19" diameter bolt holes, 2" c-c with 0.31" countersink on reverse side of o-ring. Solid aluminum.

Product Details:
1.75" diameter x 0.37" thick with centered 0.743" diameter x 0.625" long plug with o-ring. (4) 0.17" diameter bolt holes in square 1" c-c pattern. Used to plug a 3/4" (0.75") beveled chamber hole. Aluminum.

Product Details:
16-13/16"L x 1-1/2"W x 3/8"H base with two sets of side rails - your option which to use, see for dimensions and specifications. 5 Aluminum pieces.

Product Details:
16-13/16"L x 1-1/2"W x 2-1/8"H base with two sets of side rails - your option which to use, see for dimensions and specifications. 5 Aluminum pieces.

Product Details:
16-7/8"L x 1-1/2"W x 1-1/4"H base with only one set of side rails, see for dimensions and specifications. Assembled.

Product Details:
9-1/8"L x 1/2"W x 0.6"H. Rounded top and upper edges and corners. Bottom 1/4" block has square (sharp) edges. Solid aluminum, 3 tapped holes on bottom.

Product Details:
14-7/8"L x 1-1/2"W x 0.75"H1 with an inner, rounded edges peak centered on top 13-7/8"L x 1/4"W which totals 1"H2 overall. Solid aluminum 1.7 lbs.

Product Details:
14-7/8"L x 1-1/2"W x 0.75"H1 with an inner, rounded edges peak centered on top 13-7/8"L x 1/4"W which totals 1"H2 overall. Solid stainless steel 4.85 lbs.

Product Details:
14-1/8"L x 1"W x 1/8"H base with peaking elecrode 13-3/4"L x 1/2"W x 0.6" overall height, centered on base. Stainless steel, no screw points on bottom.

Product Details:
14-7/8"L x 7/8"W x 1/4"H base with square electrode peak 13-13/16"L x 0.20"W x 0.15"H making overall height of 3/8" (non-round / sharp corners). Aluminum, no screw points on bottom.

Product Details:
18-5/8"L x 1/2"W x 0.60"H. Rounded top and side corners and edges. 6 screw points on bottom, 6-32nd threaded. 5 on 4" c-c and the last 2-1/2" c-c. Solid aluminum.

Product Details:
27-1/4"L x 1/2"W x 0.60"H. Rounded top and side corners and edges. 7 screw points on bottom, 6-32nd threaded. 5 on 4" c-c and the last 6" c-c. Solid aluminum.

Product Details:
11-3/4"L x 1/4"W x 1/16" base height. One aluminum rail piece, no connecting point.

Product Details:
11-3/4"L x 0.06"W x 1/4" base height with 0.25"L x 0.06"W x 0.25"H connecting point in center of rod's length. Overall 1/2" height at connecting point. Aluminum. Would typically be embedded in (like LZR-81001-01) or between alumina ceramic.

Product Details:
11-3/4"L x 0.06"W x 1/4" base height with off-center 0.25"L x 0.06"W x 0.25"H connecting point. 4-1/4" from left side,
7-1/4" from right.

Product Details:
14-3/4"L x 0.06"W x 0.1" base height with 0.25"L x 0.06"W x 0.25" connecting point in center of rod's length. Aluminum. Would typically be placed in a groove within an alumina ceramic wall or spaced between two pieces of alumina.

Product Details:
16-1/16"L x 0.06"W x 1/8" base height with off-center 0.25"L x 0.06"W x 0.25"H connecting point. 8-1/4" from left side,
7-1/2" from right.

Product Details:
13-7/8"L x 0.19"W x 5/8"H. One stainless steel rail piece, no connecting point.

Product Details:
14-1/8"L x 1/8"W x 3/4"H with completely (half-circle) rounded edges. One polished stainless steel rail piece, no connecting point.

Product Details:
1−1/8" W x 5−15/16" L x 1.40" −to− 1.58" H No hardware included Aluminum wedges when tightened cause the height of the device to increase (similar to a wedge jack). Used to brace inner laser assembly to the housing. Center hole allows piece of allthread and nuts to squeeze wedges together.
Minimum and maximum height measured using 0.1" diameter rod, or included hardware. Some wedge shafts are threaded 1/4−20. All shafts 0.2" diameter.

Product Details:
2" W x 3−3/16" L x 0.74" −to− 0.88" H Threaded shaft and nuts included Aluminum wedges when tightened cause the height of the device to increase (similar to a wedge jack). Used to brace inner laser assembly to the housing. Center hole allows piece of allthread and nuts to squeeze wedges together.
Minimum and maximum height measured using 0.1" diameter rod, or included hardware. Some wedge shafts are threaded 1/4−20. All shafts 0.2" diameter.

Product Details:
2" W x 3" L x 0.4" −to− 0.54" H Threaded shaft and nuts included Aluminum wedges when tightened cause the height of the device to increase (similar to a wedge jack). Used to brace inner laser assembly to the housing. Center hole allows piece of allthread and nuts to squeeze wedges together.
Minimum and maximum height measured using 0.1" diameter rod, or included hardware. Some wedge shafts are threaded 1/4−20. All shafts 0.2" diameter.

Product Details:
2" W x 2" L x 0.7" −to− 0.87" H No hardware, one wedge has two 1−1/8" O.C. countersunk flathead screws Aluminum wedges when tightened cause the height of the device to increase (similar to a wedge jack). Used to brace inner laser assembly to the housing. Center hole allows piece of allthread and nuts to squeeze wedges together.
Minimum and maximum height measured using 0.1" diameter rod, or included hardware. Some wedge shafts are threaded 1/4−20. All shafts 0.2" diameter.

Product Details:
5/8" W x 4−7/8" L x 0.96" −to− 1.13" H No hardware included Aluminum wedges when tightened cause the height of the device to increase (similar to a wedge jack). Used to brace inner laser assembly to the housing. Center hole allows piece of allthread and nuts to squeeze wedges together.
Minimum and maximum height measured using 0.1" diameter rod, or included hardware. Some wedge shafts are threaded 1/4−20. All shafts 0.2" diameter.

Product Details:
3/4" W x 4" L x 0.7" −to− 0.875" H Rounded top / bottom, no hardware included Aluminum wedges when tightened cause the height of the device to increase (similar to a wedge jack). Used to brace inner laser assembly to the housing. Center hole allows piece of allthread and nuts to squeeze wedges together.
Minimum and maximum height measured using 0.1" diameter rod, or included hardware. Some wedge shafts are threaded 1/4−20. All shafts 0.2" diameter.

Product Details:
3/4" W x 3−3/4" L x 0.71" −to− 0.88" H No hardware included Aluminum wedges when tightened cause the height of the device to increase (similar to a wedge jack). Used to brace inner laser assembly to the housing. Center hole allows piece of allthread and nuts to squeeze wedges together.
Minimum and maximum height measured using 0.1" diameter rod, or included hardware. Some wedge shafts are threaded 1/4−20. All shafts 0.2" diameter.

Product Details:
3/4" W x 3−5/8" L x 0.68" −to− 0.88" H Threaded shaft and nuts included Aluminum wedges when tightened cause the height of the device to increase (similar to a wedge jack). Used to brace inner laser assembly to the housing. Center hole allows piece of allthread and nuts to squeeze wedges together.
Minimum and maximum height measured using 0.1" diameter rod, or included hardware. Some wedge shafts are threaded 1/4−20. All shafts 0.2" diameter.

Product Details:
3/4" W x 2" L x 0.61" −to− 0.75" H Threaded shaft and nuts included Aluminum wedges when tightened cause the height of the device to increase (similar to a wedge jack). Used to brace inner laser assembly to the housing. Center hole allows piece of allthread and nuts to squeeze wedges together.
Minimum and maximum height measured using 0.1" diameter rod, or included hardware. Some wedge shafts are threaded 1/4−20. All shafts 0.2" diameter.