Pressure Transducers

Product Details:
Datametrics barocel pressure sensor. 10 psi. 6" x 4" x 3"H. New!

Product Details:
Clippard Minimatics valve pressure indicator. Yellow.

Product Details:

Dwyer Instruments magnesense differential pressure transmitter. 24 vDC/vAC input. Pressure connections 3/16" tubing. Zero center scale.

• ±0.50 in WC / 100 Pa
• ±0.25 in WC / 50 Pa
• ±0.10 in WC / 25 Pa

Product Details:

Dwyer Instruments magnesense differential pressure transmitter. 24 vDC/vAC input. Pressure connections 3/16" tubing. Zero center scale.

• ±0.50 in WC / 100 Pa
• ±0.25 in WC / 50 Pa
• ±0.10 in WC / 25 Pa

Product Details:
National pressure transducer gage device. -15 - 15 psi range. Factory boxes, DC:916. Also, SZ27665

Product Details:
Transonics pressure transducer. 0 - 1000 psi range. Fluid: gas. Input: 9.999v. Output: Atmospheric 0.535, 600 psi, 9.909. 2.52" diameter x 3.9" high.

Product Details:
Servonic Instruments pressure transducer. Model H44. 5k ohm, 10 ma. 0 - 3500 psi. 3 pin circular connector for internal pot. 5 vdc reference. 1-1/2" x 1-1/2" x 4" long. 2-1/4" overall height. Units fully field tested. Possibly used.

Product Details:
Airpax DC transducer. Wire passes through 9/32" inner diameter hole @ transducer middle. 2" x 2-1/4" x 3"L. Gates / Harris P/N: 741-0001-000.

Product Details:

Transonics pressure transducer. 5 ma @ 50ºF, 7500 ohm.

• Range: 0 - 600 psi
• Fluid: Gas
• Input: 9.035v
• Output: 0.744v @ 14.7 psia / 8.719v @ 600 psia
• Dimensions: 2-1/2"D, 3-3/4" overall length

Product Details:

Vernitech infinite resolution pressure transducer. Model 2000. 10k ohm C.I.C. 3 terminal potentiometer. 1/8" male flare fitting. Small size, light weight. Low error under vibration. High voltage output.

• Pressure Range: 20 - 120 psig
• Terminal Resistance: 10k ohms ±10%
• Independent Linearity: ±0.5% F.S.
• Repeatability: ±0.1% F.S.
• Power Rating: 0.10 watts
• Life: To 10 million cycles, depending upon application
• Temperature Sensitivity: ±0.01% / °C
• Response Time: 20 milliseconds to respond to 63% of step pressure input
• Temperature Range: -55°C to +85°C
• Accleration Error: ±0.2% / G to 20G
• Pressure Media: Gage: any media compatible with Ni-Span-C, Aluminum & Stainless Steel
• Dimensions: 1-1/4"D x 1-5/8"L

Product Details:

Data Instruments Model AB Pressure Transducer features high signal level, high accuracy and low cost. Useful in tight constraint applications.

• Pressure Range: 0 - 2000 psis (Standardized gage pressure)
• Overload: 2 times rated pressure without damage
• Signal Output: 100 mv at rated pressure
• Exitation Voltage: 5v AC or DC nominal. 6v max
• Sensitivity: 20 mv / V
• Bridge Resistance: Input: 150 ohm, Output: 115 ohm (Germanium bridge)
• Accuracy: Within 1% including non-linearity, repeatability and hysteresis
• Case Material: 15 - 5 PH stainless steel
• Electrical Connection: 3 ft., 4 cond. shielded cable
• Dimensions: Flush diaphragm type, 0.749" diaphragm diameter x 0.935" mounting ring diameter. 1/4" mounting ring thickness. 1.0" OAL not including cable potting

Product Details:

National Semiconductor pressure transducer. Typical use is to apply 10-16 vdc to red / black wires. Transducer will output 16.7 millivolts DC on green and black wires for every additional psia on 1/4¢ port. This stainless body can withstand almost any liquid or gas. Practical and scientific pressure monitoring applications are endless.

• Input: 10 - 16 vdc
• Output: 16.7mv / psia
• Range: 0 - 300 psia
• 1/4" NPT port
• Vitan liquid filled diaphragm
• Stainless steel body
• Dimensions: 2-3/16"D x 4"H

Product Details:

The Schaevitz P-3000 Series pressure transducer is self-contained, DC-operated instrument designed to provide DC output voltages and currents which are linearly proportional to applied pressure. Operating from an unregulated source of 10 - 32 vdc at 1.2mA, the P-3061 model transducer provides an output of 0 - 5 vdc.

The aluminum case houses an LVDT assembly and a circuit board containing the electronics to excite the LVDT and amplify the output signal. The LVDT is coupled to a convoluted pressure capsule. The pressure capsule is designed so that its center deflection is proportinal to applied pressure. The lightweight LVDT core and rod reduce the effects of gravity on zero to less than 0.5% of full scale output per g in the lower ranges (inches of water). Built-in stops prevent damage due to minor pressure overloads. Used, removed. Includes instruction / installation manual.

• Electrical input: 10 - 32 vdc unregulated, 1.2mA operating current
• Pressure Range: 0 - 2 inches H20
• Output: 0 - 5 vdc, 5mA maximum
• Output Impedance: Less than 1 ohm
• Output Change with Input Voltage Change: Less than 0.1% from 10 vdc to 32 vdc
• Combined Static Error (Non-Linearity, Non-Repeatability, and Hysteresis: Less than ±0.5% of full range output (best straight line)

Product Details:

The Schaevitz P-3000 Series pressure transducer is self-contained, DC-operated instrument designed to provide DC output voltages and currents which are linearly proportional to applied pressure. Operating from an unregulated source of 10 - 32 vdc at 1.2mA, the P-3061 model transducer provides an output of 0 - 5 vdc.

The aluminum case houses an LVDT assembly and a circuit board containing the electronics to excite the LVDT and amplify the output signal. The LVDT is coupled to a convoluted pressure capsule. The pressure capsule is designed so that its center deflection is proportinal to applied pressure. The lightweight LVDT core and rod reduce the effects of gravity on zero to less than 0.5% of full scale output per g in the lower ranges (inches of water). Built-in stops prevent damage due to minor pressure overloads. Used, removed. Includes instruction / installation manual.

• Electrical input: 10 - 32 vdc unregulated, 1.2mA operating current
• Pressure Range: 0 - 5 inches H20
• Output: 0 - 5 vdc, 5mA maximum
• Output Impedance: Less than 1 ohm
• Output Change with Input Voltage Change: Less than 0.1% from 10 vdc to 32 vdc
• Combined Static Error (Non-Linearity, Non-Repeatability, and Hysteresis: Less than ±0.5% of full range output (best straight line)

Product Details:

The Schaevitz P-3000 Series pressure transducer is self-contained, DC-operated instrument designed to provide DC output voltages and currents which are linearly proportional to applied pressure. Operating from an unregulated source of 10 - 32 vdc at 1.2mA, the P-3061 model transducer provides an output of 0 - 5 vdc.

The aluminum case houses an LVDT assembly and a circuit board containing the electronics to excite the LVDT and amplify the output signal. The LVDT is coupled to a convoluted pressure capsule. The pressure capsule is designed so that its center deflection is proportinal to applied pressure. The lightweight LVDT core and rod reduce the effects of gravity on zero to less than 0.5% of full scale output per g in the lower ranges (inches of water). Built-in stops prevent damage due to minor pressure overloads. Used, removed. Includes instruction / installation manual.

• Output: 4-20 mA 2-wire loop
• Loop Supply: 10-31 V DC
• Loop Resistance: 1200 ohms maximum
• Combined Static Error (Non-Linearity, Non-Repeatability, and Hysteresis: Less than ±0.5% of full range output (best straight line)

Product Details:

Tyco pressure transducer. 4 pin molex I/O. 15 psi range. 100mv output. Stainless Steel Model AB sealed transducer mounted in a plastic 1/4" hose adapter. Compare to ABH015PSC1B or Data Instruments original 9220102 (probably made for Tyco back in the day). Removed from new equipment.

Sells from distributors at over $900 for minimum quantity of 5 pieces.

• Pressure Range: 0 - 15 psi
• Overload: 2 times rated pressure without damage
• Signal Output: 100 mv at rated pressure
• Exitation Voltage: 5v DC nominal. 6v max
• Accuracy: Within 1% including non-linearity, repeatability and hysteresis
• Case Material: 15 - 5 PH stainless steel

Product Details:

Data Instruments Model AB Pressure Transducer features high signal level, high accuracy and low cost. Useful in tight constraint applications. Alternate P/N: 9222505.

• Pressure Range: 0 - 2000 psis (Standardized gage pressure)
• Overload: 2 times rated pressure without damage
• Signal Output: 100 mv at rated pressure
• Exitation Voltage: 5v DC nominal. 6v max.
• Sensitivity: 20 mv / V
• Bridge Resistance: Input: 150 ohm, Output: 115 ohm (Germanium bridge)
• Accuracy: Within 1% including non-linearity, repeatability and hysteresis
• Case Material: 15 - 5 PH stainless steel
• Electrical Connection: 3 ft., 4 cond. shielded cable
• Dimensions: Flush diaphragm type, 0.749" diaphragm diameter x 0.935" mounting ring diameter. 1/4" mounting ring thickness. 1.0" OAL not including cable potting

Product Details:
Cobe Labs pressure sensor transducer. 1" MIP thread. 2 pin molex connector. Alt. P/N: 6E1730.

Product Details:
8-D pressure switch. 1/8" NPT. H/P 27 kg / cm², M/P 15 kg / cm², L/P 2 kg / cm². No other specifications.

Product Details:
Honeywell Data Instruments pressure transducer. 0 - 500 psig. Input Z: 500 ohms. Output Z: 900 ohms. 5 - 6v DC supply voltage. Output: 0 - 50mV. 1/8" - 27 NPT port. 3/16" spade "QC" terminals. OEM cost was over $175. Our price...

Product Details:
Mopar oil pressure sending unit. 1/8" NPT. Fits 1968 - 1974 Dodge Charger, Coronet, Super Bee, Challenger, Road Runner, GTX, Barracuda with oil gauge instead of light.