Roller - Lever Arm Microswitches

Roller Lever Switch
(SWM) 5930-829-5859
Microswitch roller lever switch. Military surplus. Very stiff rotary action. 4 switches: 2 normally open, 2 normally closed. 5-1/4" overall length. 3/4" MIP threaded base. 1-7/8" radius to outside roller. 8 leads are 20 feet long, high temperature wire. NSN: 5930-829-5859.
$149 each
Lox Switch
220v DC @ 500 mA
(SWZ) C2-JK2
R.B. Denison / Telemecanique lox switch. 220v DC @ 500 mA. 1PST, N.O., momentary action. 30 inch-ounces switch actuating force. Water tight. 0.50" actuator roller diameter. NOS. Mil-spec. Made in the USA. DC: 1985-1992. NSN: 5930-00-397-8483.
$195 each
Linear Roller Microswitch
DPST / N.O.
(SWM) H11-44
Control Switch Division linear roller microswitch. DPST, normally open contacts. Heavy duty 0.5"D roller on end of linear arm is depressed to make switch. 0.06" travel to make switch. 0.25" max linear travel. Six electrical contacts via 3 lug male circular connector with 5 internal keyways. Sealed casing. Fits 5/8" hole. Bushing could accomodate 1/2" to 5/8" panel. NSN: 5930-455-4367.
$127 each
Microswitch Roller Arm Snapswitch
SPDT / 125v DC @ 1/2a / 250v DC @ 1/4a / 480v
(SWM) BAF1-2RQ9-LH
Microswitch roller arm snapswitch. SPDT. 125v AC @ 10 amp, 1 HP. 250v AC @ 2 HP. 125vDC @ 1/2a / 250vDC @ 1/4a / 480v. 11-1 N operating force. 3 hole mounting. 1/2" conduit fitting. 1" x 4" x 2-1/8"H. 3-5/8" overall height.
$139 each
Roller Arm Microswitch
SPDT / 125v AC / 250v AC / 460v AC / 15 amp
(SWM) BZ-2R05GRY
Roller arm microswitch. SPDT. 15 amp @ 125/250/460v AC. 1/4" max travel on activated arm. Gray arm. 2-1/2" overall length. 1-3/8"H nominal. 1-3/16" c-c mounting holes.
$85 each
Roller Arm Microswitch
SPDT / 125v AC / 250v AC / 460v AC / 15 amp
(SWM) BZ-2R05GRN
Roller arm microswitch. SPDT. 15 amp @ 125/250/460v AC. 1/8" max travel on activated arm. Green arm. 2-1/2" overall length. 1-1/4"H nominal. 1-3/16" c-c mounting holes.
$85 each
Roller Arm Switch
600v / 20 amp Contacts
(SWZ) NL100WTRC
Denison Loxswitch roller arm switch. 600v, 20 amp contacts. Momentary: 1 - SPDT, 1 - SPST normally open. Waterproof / explosion proof. 3/4" conduit port. 2-1/4" x 5" x 1-3/4" high. Roller 1-7/8" radius. NSN: 5930-00-767-5590.
$185 each
Extended Roller Arm
15 amp - 125 / 250 / 480 vac
(SWM) 421303
Extended roller arm microswitch. 15 amp, 125 / 250 / 480 vac. Roller arm total length is 4.5". Angle mounting plates measure 1" c-c. NSN: 5930-00-058-0193.
$75 each
Snap-Action Switch Actuator
(SWM) 76-1249
ITW snap-action switch actuator. Roller lever, bracket and hardware. For ITW and similar microswitches. Actuator arm measures 1.25"L. 0.37" O.D. wheel in 0.46"H bracket. 1.14"L x 0.38"H x 0.34"W mounting bracket.
$5 each - $4 (25+)
Roller Arm Contact Assembly
SPDT
(SWX) D-735284A
Roller arm contact assembly. SPDT. Leaf contact with roller and "L" bracket. 1-1/16" c-c mounting holes. NSN: 5999-00-144-2018.
$7.75 each - $6.50 (6+)
Roller Arm Microswitch
(SWM) 65-3010
ITW Switches roller arm microswitch. 2 circuits, normally closed & normally open. 16 oz. max actuating force. 5 oz. minimum release force. Spring loaded lever with copper roller. 0.846" x 0.188". 30 vdc @ 7 amp, 250 vac @ 10 amp. 0.896" x 0.897" x 0.327" thick. 1/2" c-c mounting holes, 0.113". NSN: 5930-00-931-6028.
*** SOLD OUT ***
Cherry E23 Microswitch
SPDT / 100 ma / N.O.
(SWM) E63R
Cherry E63 microswitch with 24" leads on normally open contact with 2 pin molex connector. SPDT, 125v, 100 ma. High quality roller lever. 0.855" x 0.735"H (open position) x 0.255" wide. 0.375" c-c mounting holes.
$5.75 each - $5.25 (10+), $4.90 (25+), $4.50 (100+)
Unimax Roller Arm Microswitch
SPDT
(SWM) 2HBF-1
Unimax roller arm microswitch. Contacts: SPDT, 20 amps 125 / 250 / 480v AC, 0.25 amps 250v DC, 0.5 amps 125v DC. 0.68" thick x 1.94" long x 1.04" high body. 1.412" overall height with roller. Contacts make at 1.375". Solder terminals. 1" c-c mount holes.
$29 each - $27 (3+)
Roller Lever Actuator for Snap-Action Switches
(SWM) 71-1040
Roller lever actuator for snap-action switches. Movement differential: 0.030", ±0.015". Operating point: 0.671", ±0.031". Pre-travel: 0.093" max. Over-travel: 0.062" min. Mounting centers = 0.507" x 0.300". Originally made for ITW's Series 11 mini-switches.
$5 each
Roller Arm Bracket
  
(MIS) 8224
Roller arm bracket. 1-1/8" x 3/4" mounting plate. 0.424" deep. 0.265" wide roller, 0.164" diameter. 0.310" x 0.525" mounting hole grid. NSN: 5930-518-3189.
$7.50 each
Cherry E23 Microswitch
SPST / 5 amp / N.O.
(SWM) E23-R
Cherry E23 microswitch with 1" roller lever. SPST, 5 amp, normally open. Reduces friction on moving trigger components. 1" c-c mounting holes.
$6.90 each - $6.25 (10+)
Snap Action Switch w/Roller Arm
SPDT / 125 - 250 vac / 20 amp
(SWM) 2607-1150
McGill Manufacturing Co. snap action switch with roller arm. SPDT, 20 amp, 125 - 250 vac. 1 hp, 125 vac, 2 hp, 250 vac, 50/60 Hz. Lever = 1-1/2"L, roller = 3/8" diameter. 5/8" x 5/8" x 1-13/16". 9 oz. operating force.
*** SOLD OUT ***
Roller - Toggle Switch
2 Pole On/Off / 30 amp
(SWZ) 100006-KA
Arrow-Hart roller - toggle switch. Mounts in 2 x 4 electrical "handybox". 2 pole ON-OFF, 30 amp switch. 230 vac, 460 vac, 2 HP. 1-3/4" deep below plate. Roller extends 5/8" above plate. NSN: 5930-00-076-7074.
$17.50 each - $15 (5+), $13.75 (25+)
Lever Switch
SPDT / 15 amp
(SWM) 204695
Nylon roller tracks movement and bi-metal spring "snaps" SPDT, 15 amp contact to closed position. Great interlock switch for high current application.
$13 each - $10 (6+)
Submersible Roller Arm Switch
DPST N.O. / 440 vac / 250 vdc / 5 amp
(SWR) IC5896AIB2
General Electric submersible roller arm switch. Steel, sealed housing with 1" threaded electrical inlet. Switch contact DPST, normally open. Engages when lever rocks in either direction. 440 vac / 250 vdc / 5 amp contacts. Roller arm swings radius of 5". 2" diameter wheel. 4-1/2" x 7-1/2" x 7" high max. Very well made by G.E. Extra heavy duty.

Made for outdoor, military or underwater use. Weighs 15 lbs. NSN: 5930-00-296-6408. Government cost is $850. Our price...

$275 each
Cam Arm Switch
Lever Operated Ball Roller
(SWM) 6984H28A
Cutler Hammer hermetically sealed, water tight, enclosed switch. Arm travels 45º CCW to switch + 15º to end. Industrial grade. 1.5 amp contacts. 1- N.O. & 1- N.C. set. All metal parts are bronze or stainless. Box is PVC. Lid has rubber seal. 3" x 3-1/8" x 8" long. Arm 3" long center to roller top.
$175 each
Roller Lever Microswitch
SPDT
(SWM) MWW
Microswitch, roller lever (no brand). Contacts: SPDT. 0.545" long x .20" thick x .462" high body. 0.725" long to end of roller arm. 0.762" overall height with roller. 0.185" c-c mount holes. 7 amps, 250v AC.
$10 each
Cherry Roller Lever Microswitch
SPDT
(SWM) DG1C-B1RA
Cherry microswitch, roller lever. Contacts: SPDT. 0.5" long x .229" thick x .749" overall height with roller. 3 amps, 125v AC. 2 amps, 30v DC. Alt P/N: 132A.
$5.75 each
Microswitch® Roller Lever Microswitch
SPDT
(SWM) BZ-2R05
Microswitch Corp. ® roller lever microswitch. Type Z. Industrial cast lever arm. Contacts: SPDT, 5 amps 250v AC. 2.45" length overall including roller arm. 1.795" height overall from bottom of bracket to top of roller arm. Switch makes at 1.778". 1.19" c-c mount holes in bracket.
$39 each
Heavy Duty Roller Arm
2 Poles - 1 N.C. / 1 N.O.
(SWM) IEB6-8
Microswitch Corp. ® heavy duty roller arm switch. 2 poles, 1 normally closed, 1 normally open. 20 amp contacts. Double roller on 2-1/2"L arm. Weather sealed. 2-1/4"W x 2"H x 3/4" body. 1" mount center. 8 foot permanent 12 gauge high-temperature leads. Made in 1965. NSN: 5930-00-050-9398.
$135 each
Microswitch® Roller Switch
SPDT / 5 amp / 120v
(SWM) S33-00P
Bonnella Microswitch® roller switch. SPDT, 5 amp, 120v. Roller folds over towards contacts. Spare part for Jaguar, Triumph Daimler classics. 1" mounting center, 0.187" spade. Made in England.
$37 each - $34.50 (6+)
Roller Snap Switch
SPDT
(SWM) E23-51K
Cherry microswitch roller snap switch. SPST, normally open. 5 amp, 1/4 HP, 125 - 250v AC. 1" long lever, rests @ 11/32" above switch body. Depresses to 3/16". 1" mounting center. 0.187" spade terminals.
$6 each - $5 (12+), $4 (50+), $3.15 (200+)
Microswitch® Roller Switch
Water Tight
(SWM) BZV-2RQ9
Microswitch Corp. ® roller switch, water tight. 10 amps 125v AC, 5 amps 250v AC, 3 amps 480v AC. 1" thick x 3" long x 2.856" high including roller. 2-1/8" x 2-5/8" oval mount foot. Contact makes at 2.73". 1/2" EMT electrical mount. New in box.
$117 each
Microswitch® Roller Switch
Zinc Chromate Primed - Water Proof
(SWM) BZE-7RQ9TN
Microswitch Corp. ® roller switch. Zinc chromate primed, water proof. 10 amp contacts. 1" thick x 2-5/8" long x 1.81" high body. 2.978" overall height with roller. Switch makes at 2.961". 1/2" male electrical thread. 1" c-c mounting holes.
$115 each
Microswitch® Roller Switch
Water Proof
(SWM) BZV-2RQ9TN
Microswitch Corp. ® roller switch, water proof. 10 amps 125v AC, 5 amps 250v AC, 3 amps 460v AC. 1" thick x 3.38" long x 1.84" high body. 2.96" overall height with roller. 2-1/8" x 2-5/8" oval mount base. Switch makes at 2.955". 1/2" male electrical thread.
$115 each
Unimax Roller Switch
Water Tight
(SWM) KSR5-T
Unimax roller switch, water tight. 10 amps 125 / 250 / 480v AC, 0.25 amps 250v DC, 0.5 amps 125v DC. 1" thick x 3" long x 2.961" high with roller. Depresses at 2.936". 1/2" box connection. 1" c-c mounting holes.
$125 each